COMNAV 1460 PDF

Published by on January 13, 2022
Categories: Spiritual

Comnav Pdf User Manuals. View online or download Comnav Installation And Operation Manual. ComNav Autopilot Manual. Autopilot System Installation & Operation Manual COMPLIES WITH CE REGULATIONS PN V ComNav Autopilot ComNav Autopilot. READ. Show more . Autopilot System Installation & Operation Manual v1r3 – ComNav · comnavmarine .

Author: Mataur Goltijar
Country: Chad
Language: English (Spanish)
Genre: Music
Published (Last): 22 November 2014
Pages: 96
PDF File Size: 16.48 Mb
ePub File Size: 12.23 Mb
ISBN: 893-5-33083-377-1
Downloads: 35718
Price: Free* [*Free Regsitration Required]
Uploader: Gardakazahn

Insert the bared end of the wire into the terminal strip and fasten it there by tightening the screw on the terminal strip. If you purchased a system with a Cable Drive, one of several models will be included.

Piloto automático Comnav | Electronics – iNautia

Should the Purchaser coknav that the Equipment be returned by a faster method, the costs incurred by the expedient delivery will be pre-paid by the Purchaser; No refund of the purchase price for the Equipment will be made to the Purchaser unless ComNav is unable to remedy the defect after having a reasonable number of opportunities to do so. Next, turn to the section on Installing the Conmav Drive page If you can’t, then look for hydraulic leaks, check the hydraulic fluid level. Any attempts to remedy the defect by anyone else shall render the warranties set forth in this Agreement void; Charges for overtime, standby, holiday and per diem will not be paid by ComNav and are specifically excluded from the warranties set forth in this Agreement.

Do not blow the filings off. The terminal strips are labelled with numbers corresponding to the wiring diagrams on comnv following pages.

ComNav Autopilot Manual |

This has 40 feet You alone are responsible for the accuracy of your compass in its location. If you have a Fluxgate Compass, you will later repeat the first part out on open water. Your vessel is off course. Go to Finishing the Setup, below.

  ENTEROBIUS VERMICULARIS TEDAVISI PDF

Comnav 1460

When tightening fittings into the pump lock valve, hold the lock valve, not the motor. The first thing to check is your wiring and your navigation device. PN Control Head.

If you started this bleeding procedure right after Step 8 in the Autopilot Setup Procedure see page 42the hydraulic cylinder rod will be fully extended in one direction. Beware if you are contacted from overseas and the buyer is quick to buy.

comnav 1460

If you cannot find the problem, have the Autopilot serviced as soon as possible. To dodge around an object in the water, press and hold either the Green or Red Key. Make sure that you are navigating safely. If the vessel is not on the correct Heading, the Autopilot calculates the rudder position which will bring the vessel onto the correct Heading. Your vessel will turn more quickly than it does when you are using the Slow Speed Rudder Response.

When you have completed the bleeding, leave the equipment for the bleeding procedure attached to your hydraulic steering system. If you are using a Reversing Pump, let the Autopilot drive the Reversing Pump until it nearly stops after the rod reaches the end of its travel. Only the Sensitivity of the currently selected Rudder Response will change. Attaching the Rudder Feedback Linkage: It is best to set the slow speed Rudder Response first. Refer to the Problems during the Setup Routine section, page Fasten it coknav the end cap with commav supplied plastic nut, and tighten securely.

  BEHRINGER MDX2600 COMPOSER PRO XL PDF

An autopilot system does not reduce your responsibility for the control of the vessel when underway. Every wire must be connected to the correct terminal on its plug! Unpacking and Identification For example: The fuse is located on the top left hand corner of the board. Loosen the adjustment block that keeps the two pieces of the Rudder Feedback Linkage from sliding.

The usual mounting spot is on the dashboard within easy reach when xomnav are steering your vessel. Position the wheel as if you were going Dead Ahead, in a straight line. First, the gland for this input must be mounted on the end cap.

Use the Clip as a template to mark the holes. Make sure that it is sending information in the correct NMEA format. Otherwise, we’ll assume you’re OK to continue.

You should keep pressing the Green or Red Key until you are well clear of the object — and until the boat will pass it clear when back on Course. Remove the inner end cap. Select comnavv following parts from the Autopilot package: All the lights will briefly turn on for self-testing purposes, followed by the Pilot light only being on the Speed light may also be on.

The light beneath the Green Key will stop flashing.

Do a final check of your hydraulic installation for any leaks or loose components.