Beninca Brain 24 Manual. Instruction Manual for Beninca Brain 24 Control Panel. Copy to Email · Send to Mobile. Print. Download · Buy Product. Name. 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 8k2 Command central for 1/2 24Vdc motor, for single or sliding doors: BRAINY Beninca Brain 24 – EasyGates Manuals & Guides. L Rev. 02/06/02 CENTRALE DI COMANDO CONTROL UNIT STEUEREINHEIT CENTRALE DE.
|Published (Last):||19 December 2011|
|PDF File Size:||9.80 Mb|
|ePub File Size:||3.88 Mb|
|Price:||Free* [*Free Regsitration Required]|
The output has the function of 2nd radio channel: Regulates the delay time benjnca motor 2 on opening with respect to motor 1 Mot.
Example of programming Let us beninva it is necessary to: If the code is valid, it is stored in memory and OK appears. By pressing ‘print’ button you will print only current page. Function Description Motor 1 Connection, motor 1: Comments to this Manuals Your Name. OFF Sld Enables or disables slowing.
Beninca BRAINY24 24Vdc Control panel for 1 or 2 motors REPLACES BRAIN24
If the code is valid, it is erase and Brsin appears. It’s a community-based project which helps to repair anything. For the light control use the auxiliary relay. Comply with regulations in force! The step-by-step impulse or transmitter impulse has no effect during the opening phase. With 2ch logic Off: Page 5 The logic menu allows you to activate or deactivate a function, in the same way as setting a dip-switch. Receiver enabled for rolling-code and benjnca code transmitters self-learning and Dip Switch.
Beninca BRAIN 24 Operating Instructions Manual
Electric lock with latch, normally not fed. The operation mode of the amperometric sensor is selected ei- ther the limit switches are provided or not.
The performance of the output is preset by 2ch parameter, see previous parameter. Similarly to the safety edge activation, the control signal is sent to stop and reverse movement beninxa approx. The control signal is sent to stop the movement.
BENINCA BRAIN 24 OPERATING INSTRUCTIONS MANUAL Pdf Download.
The logic menu allows you to activate or deactivate a function, in the same way as setting a dip-switch. The speed of the motor during braking is determined by the SLDS parameter value.
Radio receiver enabled only for rolling-code transmitters. Press the transmitter key to be assigned to this function.
The transmitter codes braim not erased from the receiver. Blinking is activated 3s before the motor starts. An incorrect setting of these parameters may result in an hazard.
If the battery charger board Benicna. Returns the control unit to the default values. For example, with a 20s stroke, preset beninc to start the braking phase, 3s in advance with respect to end of movement. Receiver enabled for rolling-code and programmable code transmitters self-learning and Dip Switch. OFF Blc The lock function is enabled or disabled.
Confirmation of operation is required. Page of 9 Go. The parameters menu allows you to assign a numerical value to a function, in the same way as a regulating trimmer. The value is expressed in percentage with respect to speed during normal operation.
With the gate open or in the opening phase the intervention of the photocell causes automatic closing after 3 s.
Got it, continue to print. For example, brwin the leaves completely closed the display is as follows: The preset time should therefore be lower than the real stroke of the operator. The operating time is adjusted at normal speed during motor 2 opening and closing phases.
At the end of the set time the control unit orders a closing manoeuvre.
If buffer batteries are used, connect the CB. OFF mloc Selects the type of electric lock used. Active only with TCA: Parameters, Logic and Special Functions The tables below describe the individual functions available in the control unit. Before each opening manoeuvre the braih supply is interrupted for the time set by the parameter TLOC.